Quote visits 24/7Book online any day, any hour
Licensed and insured MA HIC #655031Peabody showroomMon to Sat
A remodeled bathroom with a freestanding tub, a double vanity and a glass shower
Bathroom RemodelingTubs, vanities, tile and fixtures
A walk-in shower with marble tile and frameless glass doors
Showers & Glass DoorsWalk-in showers, benches and glass doors
A tiled shower with a lit niche and an accent band
Niches & Accent TileShower niches, mosaics and borders
A remodeled kitchen with white cabinets, an island and pendant lights
Kitchen RemodelingBacksplashes, floors and full kitchens
A room with a new herringbone tile floor
Tile FloorsKitchens, baths, entries and patterns
A tile floor with a custom medallion at its center
Custom Tile WorkPatterns, borders and one-off details
A room being painted, with taped edges, a roller tray and drop cloths
PaintingWalls, ceilings, trim and doors
Built-in shelves and a new wood staircase
CarpentryTrim, doors, framing and built-ins
A whole house remodel shown floor by floor
Full RemodelsEvery room, start to finish
A stone patio with a fire pit and outdoor chairs
Outdoor PatiosStone and tile patios

Refinish or replace your hardwood floors.

How to read the floor, what each job involves, and when you can walk on it, move the furniture back and put the rugs down.

Updated November 2026. The sources are at the end of the page.

(978) 595-9993
Oak floors sanded and refinished by Becker in StonehamA drum sander taking the old finish off a hardwood floorA refinished oak floor in a bright room on a Becker job in Stoneham

The short answer

Most worn hardwood can be refinished.

If the boards are sound and there is enough wood left above the tongue, refinish. A dull floor with light scratches often needs only a new coat of finish. Deep scratches, dents, worn traffic lanes, bare wood or a change of color call for a full sand and refinish. Replace the boards that are buckled or already sanded too thin, and only those, when the rest of the floor is sound.

On our jobs a floor takes from one day to a few weeks, depending on the size, the repairs and the finish. Afterwards, Bona, a finish maker, says its floors can take socks in 3 to 4 hours, furniture in 48 hours and rugs in a week. Other finishes take longer, so ask which product goes on your floor.

How to tell

Reading the floor before you decide.

The National Wood Flooring Association (NWFA) separates the jobs by how deep the damage goes. Most scratches are in the finish, not in the wood, and a floor that only looks dull can be renewed with a new coat. Once the damage reaches the wood, the floor needs sanding.

  • Dull, with light scratches. A maintenance coat: the finish is cleaned, lightly sanded and recoated.
  • Deep scratches, dents, wear patterns or bare wood. A full sand and refinish. The NWFA also recommends sanding to raw wood when you want a new color.
  • Permanent cupping. Boards with raised edges that stay that way after the house has dried out need sanding, not a recoat.
  • Buckling. A buckled wood floor has to be replaced wherever it buckled.
  • Water damage. First find and stop the source of the water. Minor damage often fades or disappears as the floor dries, and the subfloor underneath has to be checked as carefully as the wood on top.
  • Sanded through. When an earlier sanding went through the top layer of an engineered floor and stain cannot hide it, the usual result is replacing those boards.

Solid or engineered

How many times a floor can be sanded.

It depends on how much wood is left above the tongue, called the wear layer. The NWFA magazine puts it this way:

  • Solid wood. Most solid wood floors can be sanded six to eight times over their life. Their wear layer is usually about 1/4 inch or more.
  • Engineered wood. The top layer of real wood ranges from 1/16 inch to 1/4 inch. Engineered floors can usually be refinished, but not as many times as solid wood.
  • Each sanding. A traditional sand job removes about 1/32 to 1/16 inch of wood.
  • The floor line. Where the wear layer is under 3/32 inch, sanding is not recommended.

A good contractor measures before quoting a refinish: at a floor register, where a threshold has been removed, or with a gauge, in more than one spot. The count also depends on the skill of the person sanding, the machine, and how flat the floor is.

Two different jobs

Screen and recoat, or a full sand and refinish.

Screen and recoat (the NWFA calls it a maintenance coat) works on the finish only. The floor is cleaned, the old finish is lightly abraded so the new coat can bond, and a fresh coat goes on. It works on the finish rather than the wood.

A full sand and refinish takes the floor back to bare wood. Bona describes the steps for its own system:

  1. Sand to bare wood, with dust containment on the sanders.
  2. Sealer or stain, for the color you choose.
  3. Finish coats. Bona says the standard for a hardwood floor is at least three coats in all.

Bona says a floor done this way is ready for use again within 2 to 4 days. A good contractor repairs loose or damaged boards before the sanding starts.

After the finish

Walking on it, furniture and rugs.

These times come from Bona, for its own finishes. They vary by product, and the temperature and humidity in the house change the dry times.

  • Walking in socks. 3 to 4 hours.
  • Furniture back. 48 hours. Set it down, never drag it, and put felt pads under the legs.
  • Rugs. One week, when the finish is fully cured. Until then the finish scuffs and scratches more easily.
  • Pets. Keep them off the floor until the finish is fully cured.

Acid cured finishes are a different case: Bona says they dry fast but can take 30 to 90 days to fully cure, keep releasing fumes while they do, and require the family, pets and plants to leave the house during the work. Rugs stay off longer with those. Ask what finish is in the quote.

Living with the work

Dust, and whether you move out.

Sanding is the dusty part. Bona says its dust containment systems virtually eliminate airborne dust and that, with its waterborne finishes, you may not need to leave the house. Rooms being sanded and finished still have to be empty.

On our jobs the work area is closed off and cannot be used, the rooms next to it are protected, and the site is cleaned every day, with a final cleaning at the end. See getting the house ready.

Older homes

Carpet, winter gaps and painted floors.

  • Look under the carpet. Before pricing a new floor in an older house, lift a corner of the carpet inside a closet and see what is underneath. If there is wood, have it measured for a refinish first.
  • Gaps in winter. Wood shrinks when the heat is running and swells in humid summers. The NWFA calls this normal and suggests keeping the house between 60 and 80 degrees and 30 to 50 percent humidity all year. Gaps that do not close in the humid months are a reason to call a professional.
  • Painted floors. If any part of the floor or the stairs is painted and the house was built before 1978, sanding it disturbs a painted surface, and the EPA lead rule applies to anyone paid to do that work. See our lead paint guide.

Questions

What homeowners ask about hardwood floors.

How long does it take to refinish hardwood floors?

On our jobs a floor takes from one day to a few weeks, depending on the size, the repairs and the finish. Bona says a floor sanded and finished with its system is ready for use again within 2 to 4 days.

How long after refinishing hardwood floors can you walk on them?

Bona says its finished floors can take stocking feet in 3 to 4 hours. Times vary by product, and the temperature and humidity change the dry times.

When can I put furniture back on refinished floors?

Bona says 48 hours for its finishes, with the furniture set down, not dragged, and felt pads under the legs. Acid cured finishes take much longer to cure.

When can I put rugs back after refinishing?

Bona says one week, when its finish is fully cured. For acid cured finishes, which can take 30 to 90 days to cure, rugs stay off much longer.

How many times can hardwood floors be refinished?

Most solid wood floors can be sanded six to eight times, according to the NWFA magazine. Engineered floors have a thinner top layer, from 1/16 to 1/4 inch, and sanding is not recommended once it is under 3/32 inch.

Is it cheaper to refinish or replace hardwood floors?

It depends on the floor. Refinishing keeps the wood you already have when the boards are sound and there is wood left to sand. Replacement is for boards that are buckled or sanded too thin. Our hardwood cost page has published Boston ranges for both, and the quote visit, usually free, is the place to look at your floor.

Let’s build it.

Tell us about the job. We answer right away and book the visit.

(978) 595-9993

Tell us about the job. We answer right away and book the visit.

(978) 595-9993

Let’s build it.

Let’s build it.

Tell us about the job. We answer right away and book the visit.

(978) 595-9993